Corner notcher NM-3 is used by enterprises who specialize in manufacturing of facade cassettes with different configurations and complexity. It allows you to optimize the preparing process, saving time on the corner punching operations of the future facade cassette of the required shape. This corner notcher is equipped with a special tool, consisting of a die and a punch, and makes it possible to punch a complex angle of the facade cassette in just one operation. Corner of NM-3 façade cassette consists of several 90 degrees angles and radius groove, which prevents possible deformation of the metal in the corner of the façade cassette during future bendings. Corner notcher NM-3 is also equipped with special equipment for cutting an oval hole for fixation bolts on the façade cassette. So, using this equipment, our customer can cut both: a complex corner of the cassette and the fixation bolt hole in one operation without wasting time on doing it on different machines and saving time and money on preparing cutting and punching works. We use special tool steel to make dies of punching press. Those dies are tempered to get necessary hardness and working resistance. To get necessary roughness of corner notcher working tool we use special grinding machines. Corner notcher NM-3 is manual driven so not require connection to electrical networks or air supply systems. Corner notcher NM-3 is driven by a special handle that transmits the force to the working mechanism of the machine. When using the punching press, it must be installed on a flat surface-table and fixed with special clamps or fastening mechanisms to prevent the machine from moving during operation. On request, it is possible to manufacture corner notchers to produce shapes of cassettes with different configurations according to customer preferences
Cut-to-length slitting machine is used for longitudinal cutting of the metal sheets with maximum thickness 1mm, aluminum composite panels, paper, polycarbonate thanks to special cutting knives that are fixed on rolls of the slitting machine. This cut-to-length slitting machine lets you to cut the material into eight strips. The diameter of the rolls is 56 mm There are four types of the sheet metal cut-to-length machines we make: The manual cut-to-length slitting machine (cutting for 2 strips) The electric cut-to-length slitting machine (cutting for 3-4 strips) The electric cut-to-length slitting machine (cutting for 6-10 strips) The electric cut-to-length slitting machine (cutting for 12-20 strips) The operator of cut-to-length slitting machine can easily change the width of the strips and their numbers. There are special screws on the knives to do it. You can easily cut sheet metal right from the decoiler with our cut-to-length slitting machine. Cut-to-length slitting machine could be equipped with cross cutting knife. The machine has strong base to avoid deformation while cutting and lets to cut metal into 8 strips with the perfect quality. The cutting speed of the slitting machine is about 10 meters/minute. Cut-to-length slitting machine is electric so it doesn’t need any air or oil system to work. Electric consumption is 1.1 kW/hour. The voltage is 380V. It could be used in environment with temperature from -10 to +45 Celsius degrees. Our enterprise has started to produce this kind of cut-to-length slitting machine (slitter) since 2008 so we have great experience in doing our job and can propose great solution to your business. To get more information about the price of this slitting machine and the way it could be delivered to your location just contact us. We will give you all the information you may need.
In this variant of electric cutting machine our customer desired to cut metal sheets from width 350mm into 12 strips. The width of one strip is 31.4mm Maximum metal thickness 1 mm Numbers of the strips – 12 The diameter of the rolls of the machine is 50 mm The diameter of cutting knife is 77mm The slitting machine SM 350 was designed by our company to let the opportunity to cut metal into length for 12 strips. The standard variant of slitting machine proposes you to cut metal from coil or metal sheets with width 1250mm for the number of strips you need. But according to our customer’s preferences we can produce special slitting machine for cutting in length metal with width from 100 to 1250mm. The maximum thickness of metal could be 1mm. According to our customer’s preferences our machines can be used for cutting into length metal sheets for 2-20 strips. The variant of slitting machine into 2 strips can be manual. The slitting machines for cutting more than 5 strips has to be with stronger base to avoid the deformation of rolls while cutting In this variant of electric slitting machine our customer desired to cut metal sheets from width 350mm into 12 strips. The width of one strip has to be 31.4mm The operator of this slitter machine can easily change the width of one strip or the total number of strips using special screw on the knives. This screw lets to unfix knife of the machine and change position of it. The speed of cutting is 10 meters per minute for the machine. The engine power is 1.5kW The voltage is 380V The diameter of roll is 50 mm The diameter of knife is 77mm The number of knives is 12 You can add for the slitting machine cross cutting knife as an option. As an option we also propose length measuring device for the machine. We produced machines for working with metal sheet such as: bending machines, rolling machines, cutting machines, punching presses, profiling machines, seaming machines etc.
Manual guillotine metal shearing machine MG-1250 is a machine for cutting metal sheets 1250 mm length and 1mm maximum thickness for pieces. Manual guillotine metal shearing machine is a machine that used mostly for preparing operations. The goal of those operations is to get the metal sheets with necessary dimensions for further operations such as bending, cutting, forming, punching etc. To avoid moving of metal while cutting, there is a special press-fixation system, so the metal sheet is fixed while cutting and the quality of cutting is high. There are special adjustable fixators behind the manual guillotine shear so you can get one size all the cut pieces. This way of cutting with using fixators behind the manual shear provides better quality of cutting than way of cutting with using marks on the metal sheet. The cutting knives of the manual guillotine shear are tempered and polished. They have four working edges, so when the one of working edges is not sharp enough you can change it to another one by rotating the knife and continue the process of guillotine using. We produce four models of manual guillotine shears Manual guillotine metal shearing machine MG-1250mm; Manual guillotine metal shearing machine MG 1500 x 1mm; Manual guillotine metal shearing machine MG 2010 x 1mm; Manual guillotine metal shearing machine for cutting trapezoidal panels; To cut the metal sheet with our manual guillotine metal shearing machine you have to put the metal on the guillotine table and move it to the fixators behind the shear. Before you have to place fixators to the length-position you need, so the cut pieces will be one length-size according to the position of fixators. After you have to turn the handle of pressing-fixation system and fix the metal sheet with it. So the metal sheet will be fixed while cutting. After you can cut the metal by using the cutting handle. Manual guillotine shears are widely used in process of working with other machines such as: decoilers, slitters, bending machines, plate rolling machines, forming machines etc. We have started producing of manual guillotine shears since 2003 y. So we have a great experience in shears producing and can propose you a perfect solution for you tasks.
Notching machine NM-2 for façade cassettes is used to cut multi angles in metal sheets up to 1.2 metal thickness. Multi angles are necessary to be made for further bending metal sheet in boxes, façade cassettes etc., so bending can be done from all four sides of metal sheet. Notching machine NM-2 cuts shape for façade cassettes of open type. Shape of cutting has special radius element in one of angles, so it helps to keep metal without deformation while bending. Façade cassettes that can be made using NM-2 notching machine has special shape so it prevents water to get inside cassette because angles of cassettes are closed. Notching machine NM-2 cuts multi angle without additional holes for drainage or fixation operations. But if it’s necessary we can offer it as additional options or as NM-3 model: Using notching machine NM-2 you will save time for preparing operations while façade cassettes production. It can help you to make production process faster and more efficient. Our notching machine is hand operated so it doesn’t need any air or electricity to work. NM-2 is mobile machine, so you can take it easily anywhere you want. Knives of notching machine are made from tool steel. They go through tempering and grinding processes to get necessary hardness and roughness. So we have high quality cutting tools on our notching machines. Also we have possibility to make tools for presses according to customers’ requests and change form of shapes and sizes. It lets our customer to get results they want. There is equipment that can be used with our notching machine NM-2: - Manual shears; - Segmented bending machines
Punching press for façade corner cassettes is used in the production process of special configuration facade cassettes for covering corners of different buildings. At the beginning of the manufacturing process, sheet metal is cut into blanks of required size using guillotine shears, slitting machines or cutting roller blade of a bending machine. After that, corners of the required configuration for the facade cassette are cut on the sheet blank using die-cutting presses. Standard punching press for facade cassettes allows you to optimize the process of cutting corners of facade cassettes used for cladding facades of buildings. But when assembling cassettes on a building, it becomes necessary to cover not only face but also corner of building. For such a procedure, the blank of the facade cassette should be not only with cut corners, but also with special triangular notches at the top and bottom of the sheet, which makes it possible for further bending this blank into a corner cassette and easily put it on the corner of the building being under restoration. So, to manufacture of corner facade cassettes, our customers will need both: conventional die-cutting press for facade cassettes (NM-1, NM-2, NM-3 or NM-4) for cutting the main corners of the future facade cassette, as well as special press for corner cassettes, which allows on the workpiece with already pre-cut corners, cut additional triangular elements for the future corner facade cassette. So having this equipment, you can optimize and speed up the preparation work process of the corner facade cassettes manufacturing. So, after it can be bended on a segmented bending machine with two or three segment bars to desire product.
The sheet metal slitting machine (slitter, cut-to-length machine) is used for longitudinal cutting of the metal sheets with maximum thickness 1mm, aluminum composite panels, paper, polycarbonate. This sheet metal slitting machine lets you to cut the material into four strips The diameter of the rolls is 56 mm There are four types of the sheet metal slitting machines we make: The manual sheet metal slitting machine-slitter (cutting for 2 strips) The electric sheet metal slitting machine-slitter (cutting for 3-5 strips) The electric sheet metal slitting machine-slitter (cutting for 10 strips) The electric sheet metal slitting machine-slitter (cutting for 20 strips) The operator of the sheet metal slitting machine-slitter(cut-to-length machine) can easily change the width of the strips and their numbers. There are special screws on the knives to do it. You can easily cut sheet metal right from the decoiler with our sheet metal slitting machine. The sheet metal slitting machine (slitter)could be equipped with cross cutting knife. For cutting sheet metal into more than 4 strips we provide our sheet metal slitting machines (cut-to-length machine) with stronger construction to avoid any unwanted deformation and to let you the opportunity to work with our machine the way you want. The cutting speed of the slitting machine is about 10 meters/minute. The sheet metal slitting machine is electric so it doesn’t need any air or oil system to work. Electric consumption is 0.75 kW/hour for this slitting machine. The needed voltage is 380V. It could be used in environment with temperature from -5 to +45 Celsius degrees. Our enterprise has started to produce this kind of the sheet metal slitting machine (slitter) since 2008 so we have great experience in doing our job and can propose a great solution to your business. To get more information about the price of this slitting machine (slitter machine)and the way it could be delivered to your location just contact us. We will give you all the information you need.
Sliding clip formers are used to produce fixation sliding clips for double standing seam roofing panels. Before installation roofing panels have to be made using roll former roofing machines. After finishing of panels production and preparing roofing works panels can be installed on roofing place with special fixation clips. Those clips, depending on design, could be fixed or sliding ones. Fixed clip has simple and cheap design so it can be good for small roofs that doesn’t have long length panels. Sliding clip are good for big roofs with different designs and long-length panels. Sliding clips can move and self-find perfect position so not be damaged and safe for roof while temperature expansions. We offer punching presses for making both fixed and sliding clips. For sliding expansion clips productions there have three presses to be used. First sliding clip bottom part press is used for punching bottom part of sliding clip with fixation round holes and connection oval hole. At the same time this press cuts metal strip with necessary length. Blank for clip production is easy to get using manual guillotine or cut-to-length slitting machine. Second sliding clip bottom part bender is used for bending of sliding clip bottom part to 90 degrees angle. So, after this operation bottom part is ready. Third clip former makes top part of sliding clip at the same time forming and bending it. After producing bottom and top part of sliding clip you can easily connect it to one working sliding clip. So using sliding clip formers that we offer you can easily make expansion clip and use it while double standing seam roofing installation without any unnecessary deformations. Maximum metal thickness you can work with -1mm. To get more information about sliding clip former we produce please contact our sales department.